Emergency & LeaksEmergency PlumbingWater Leak RepairSlab Leak DetectionWhole-Home RepipingGas Line RepairDrains & SewerDrain Cleaning & Sewer RepairMain Line Sewer CleaningSewer Camera InspectionGarbage DisposalWater Heaters & Water SystemsWater Heater RepairWater Heater InstallationTankless Water HeatersWater FiltrationPressure Regulator (PRV)Fixtures & MoreToiletsFaucets & FixturesShower & Tub ValvesKitchen & Bath InstallsOutdoor Hydrants & SpigotsCommercial PlumbingInspection & MaintenanceJob Stories About Reviews FAQ Contact Book Now Call (918) 891-1737 Book Online Text Us Request Service
Acts of Service Plumbing · Family-owned plumbers serving Tulsa

Gas Leak Repair and Gas Line Hookups in Tulsa

Answer

The short answer

We find and fix gas leaks, run pressure tests for the city inspection and connect gas lines for standby generators in Tulsa. You get a flat-rate, upfront price before any work starts. A service call starts at $89 and is waived when you approve the repair.

Real jobs

Recent jobs in Tulsa

  • Gas shut off for leaks. The gas company had plugged the meter. We pressure-tested the system and found three leaks in the first hour, one at the meter riser and two in the water heater closet. We reset the riser and rebuilt the closet line with a union. Read the job story.
  • Standby generator hookup. The flex line that came with a new Generac generator was too short. We added a 3/4-inch 90 and a gas shut-off valve, connected the flex line, bled the air and tested it. Read the job story.
Safety

If you smell gas

Leave the house first, then call the gas company from outside. Once the gas is shut off, we find and fix the leaks and get the line ready for inspection.

Pricing

Starting prices

  • Whole-house gas pressure test: starts at $477
How we help

Service in Tulsa

See gas line repair or all our Tulsa plumbing.

Page last updated November 2026.

From our work

The first three leaks were not the end of the test

The Tulsa homeowner's meter had been plugged, so we began by looking for leaks throughout the system. We checked accessible gas fittings outside, in the crawl space and indoors using an air-pressure test. Within the first hour, we had identified three faulty connections: the customer-side riser nipple beside the meter and a pair of connections in the hallway water heater closet. The problem was not confined to the fitting visible outside. Each of those three connections needed attention before we could test the system again.

To rebuild the closet connection, we first had to cut the pipe because it lacked a union. We added that service connection during the repair. The riser work and closet repairs did not resolve the pressure loss: the next fifteen-minute check still showed a drop. We had already checked the accessible joints, so we opened the closet wall. Inside was a leaking galvanized thread protector. We replaced it with a coupling, then watched the gauge for another full fifteen minutes. This time the pressure held.

We also capped the old floor furnace as the homeowner requested and connected the water heater vent. Our crew obtained the City of Tulsa gas permit and arranged the inspection, which passed. After a gas inspection passes, the inspector contacts ONG to release the meter. Read the full Tulsa gas repair story for the repairs and the pressure checks that led to that inspection.

From our work

A generator connection was a fitting problem, not a leak search

On a separate Tulsa visit, an electrician needed the gas connection finished for a standby generator. The flex connector supplied with the generator fell short of the house line. A three-quarter-inch elbow and a dedicated shutoff valve gave us the connection we needed. We attached the flex line to that valve, bled the air out and checked the fittings and generator operation. Read the generator hookup story for that installation, rather than the meter-shutoff repair described above.

Michael describes gas work as including existing fixtures, new fixtures, new locations and repairs to leaks. For a suspected leak, the safety instruction on this page comes first: leave the house and contact the utility from outside. The pressure readings and test duration in our repair story describe what our plumber did on that system, not a homeowner procedure for restoring a shut-off meter.

Questions

Straight Answers

My gas meter was plugged. What happens next?

The leaks have to be fixed and the line has to pass a city inspection before the gas can be turned back on. We find the leaks with a pressure test and make the repairs.

Can you connect a standby generator to my gas line?

Yes. In Tulsa we added a shut-off valve and fittings so a new Generac generator could connect, then tested it.

How much is a gas pressure test?

A whole-house gas pressure test starts at $477.

Why did you open the water heater closet wall on the Tulsa gas job?

The gauge still lost pressure after the exposed fittings were repaired, and opening the wall revealed another leaking connection.

Who contacted ONG after the Tulsa gas inspection passed?

Once the city inspection passes, the inspector contacts ONG so the meter can be released and gas service restored.

Did the generator job require replacing the supplied flex line?

No. We added an elbow and a shutoff valve so the supplied flex line could reach the generator connection.

Acts of Service Plumbing service van at the shop
Acts of Service Plumbing

Real Techs. Real Answers.

Every job on this page is answered the way our own crew describes it — no scripts, no upsells.

Call Acts of Service Plumbing

Open 24 hours Monday through Saturday · Closed Sunday

(918) 891-1737