The short answer
The three most common signs of a slab leak are a water bill that is higher than normal, spots on your floor (especially tile) that feel extremely hot or extremely cold, and a water meter dial that keeps spinning when nobody is using water.
Signs you can check yourself
- A higher water bill than normal, with no change in how you use water.
- Hot or cold spots on the floor. Tile is where you notice it most. A hot spot usually points to a hot water line.
- A spinning meter. The dial on the meter in your front yard should not move when no water is running.
The 2-minute meter check
- Turn off every faucet and every appliance that uses water.
- Go out to the water meter in your front yard.
- Watch the dial. If it still moves, water is leaking somewhere.
A moving dial does not prove the leak is under the slab, but it tells you it is time to call.
How a slab leak is found
We bring in a dedicated leak-location specialist, Dylan Nelson of Help Services. He uses sonar equipment to listen underground and usually pinpoints the pipe size and the location and depth of the leak to within six inches. He gives a report to you and to us.
Repair through the slab or reroute
You choose. We can open the slab and fix the pipe, or, about 75% of the time, reroute the water line through the attic and back down the wall and abandon the old line under the slab. Then nobody has to break through your floor. If your home has older red and blue PEX, there is usually more than one bad line, so replacing it all often makes more sense.
Slab leak repair with Acts of Service Plumbing
Slab leak detection starts at about $350, and slab leak repair starts at about $3,000. You get a flat-rate, upfront price before any work starts. We also talk with your insurance company for you. See slab leak detection, whole-home repiping or read a real slab leak reroute job story.
Page last updated November 2026.
Find the leak before opening the floor
Michael names the bill, floor temperature and moving meter as warning signs. His next step is locating the leak, with a report supplied to both the customer and the plumbing crew. A warm patch or a moving meter tells you to investigate; the leak-location report helps us decide where and how to reach the damaged pipe. The specialist's finding also helps distinguish the hot-water side from the cold-water side.
In the Owasso hydrant-line reroute, water appeared on the kitchen floor from beneath the cabinets. The homeowner shut off the house supply and chose a regular appointment. Michael and Conner tested the plumbing before the leak-location visit. The located pipe was half-inch copper beneath the slab serving an outside hydrant.
The repair kept the wall connection to the hydrant and used a new half-inch route down the kitchen wall. A water-restoration company was also referred because there was water damage. That job shows a particular reroute; it does not mean the same path is available in every Tulsa house.
Some repairs still require floor access
The August 17 Claremore job used direct access through hardwood and concrete. Once the pipe was exposed, the crew removed the leaking half-inch copper section and joined expansion PEX with press-to-expansion adapters. The access estimate anticipated a larger pipe, but the exposed leaking section was half-inch copper. The repair record identifies what the crew actually found and replaced beneath the floor.
The crew checked the repair by pressurizing from the meter, closing it for ten minutes and reopening it. Pressure held, and a video recorded the meter staying still. The scope included filling the opening and returning concrete level with the existing surface; it did not promise replacement hardwood. Read the direct-access slab repair to compare that approach with a reroute.
These are examples from Owasso and Claremore, not Tulsa job claims. They show the two repair choices Michael describes: open the slab to reach the damaged pipe, or stop using that buried line and reconnect through an accessible wall or overhead route.
A second leak changes the discussion
Michael says repeated leaks close together are the point at which he discusses a whole-home repipe estimate. One repair does not automatically require a repipe. His concern is another slab leak within a couple of months, because repairing one spot may leave the homeowner facing another leak elsewhere on the same system.
Our repipe service describes the typical two-to-three-day schedule, keeping the family home and interrupting water during tie-ins. It also separates plumbing access from drywall finishing, which our crew does not do. The owner describes larger-job payment as half upfront and half after inspection passes.
Straight Answers
What are the signs of a slab leak?
A water bill that is higher than normal, spots on your floor (especially tile) that feel extremely hot or cold, and a water meter dial that keeps spinning when no water is being used.
How do I check for a hidden water leak?
Turn off every faucet and water-using appliance, then watch your water meter. If it still moves, water is leaking somewhere.
How do you find a slab leak?
A dedicated leak-location specialist uses sonar equipment to listen underground and usually pinpoints the leak to within six inches.
Do you have to break up the floor to fix a slab leak?
Not always. About 75% of the time we reroute the water line through the attic and abandon the old line under the slab.
How much does slab leak repair cost in Tulsa?
Slab leak detection starts at about $350 and repair starts at about $3,000. You get a flat-rate, upfront price before any work starts.
Does a warm tile tell you exactly where to open the floor?
No. Michael treats floor temperature as a warning sign and uses a separate leak-location report before selecting the repair.
Did the direct-access repair include replacing hardwood?
No. The Claremore example included filling and leveling the concrete, not replacement hardwood flooring.
Does one repaired slab leak automatically require repiping?
No. Michael starts the repipe discussion when leaks recur, especially close together.
Make a short symptom record before the visit
A useful leak report can fit on a piece of paper. Write down the bill that changed, the room where you noticed a temperature difference and what the meter did with fixtures off. These are observations, not a diagnosis. Keeping them separate helps avoid turning “the tile feels warm here” into “the pipe must be directly below this tile.”
If you have the previous bill, keep it with the new one. Note any change in household water use rather than comparing dollar amounts alone. Michael recommends watching for water use that rises without an explanation. You do not need a spreadsheet or an exact leak calculation to make that concern worth a call.
For a floor-temperature concern, describe the surface and room in ordinary words. “The tile by the kitchen cabinets feels much warmer than the rest” is enough. Avoid pulling up the flooring to investigate. Locating the line is a separate service, and the eventual repair path may not follow the first place you noticed a symptom.
Treat the meter check as a question with a limited answer
Before watching the dial, make sure nobody else in the home is about to run a faucet or start a water-using appliance. Let the household know what you are checking. If someone uses water during the observation, that movement cannot distinguish ordinary use from a leak. If you are not sure everything was off, tell us. That helps us understand what the check can and cannot tell us.
The helpful result is simple: the dial moved, or you did not see it move during the check. Record that result along with the other clues. A moving dial tells us water is being used or escaping somewhere; it does not identify a hot line, a cold line, an underground location or the size of the damaged section. We need to diagnose and locate the leak to answer those questions.
Also mention visible water at fixtures or outside. A floor symptom should not make you ignore something you can actually see. We need the whole description, not just the part that seems to match a slab leak. If water starts coming through the floor, stop treating this as a quiet monitoring exercise and follow the emergency slab-leak instructions.
Do not mistake the finding for the access plan
Once the leak is located, ask us to explain two things: what line is leaking, and how the crew proposes to reach or replace that run. The location describes the problem. The access plan describes the work in your house. They are connected, but they are not the same piece of information.
The two repairs linked above took different routes. The Owasso hydrant supply repair avoided opening the slab by using a wall route. The Claremore copper repair required opening the finished floor and concrete. Your Tulsa home's layout will help determine which route works. Ask us to explain why the proposed path fits your plumbing before approving the work.
If a repair involves opening a finished surface, ask what will remain when the plumbing work is complete. Concrete patching and replacement flooring are different tasks. If an overhead or wall route is proposed instead, ask where access will be needed. A clear description before approval is more useful than assuming “no slab opening” means no access work anywhere.
Bring the history, not a conclusion about the pipe
Tell the plumber about earlier leaks, even if you do not have the invoice. An approximate description of the room and the type of repair is a starting point; paperwork is better when available. Do not assume a warm area means the earlier repair failed, or that a second symptom is necessarily the same line. We still need to find the source of the current leak.
Repeated repairs are a reason to discuss the wider system. We still need to locate the leak before recommending whether to repair one section or replace more piping. Ask for the repair scope and, when Michael recommends considering it, a separate repipe scope. That lets you compare what each choice addresses without confusing one damaged section with every water line in the home.

