Emergency & LeaksEmergency PlumbingWater Leak RepairSlab Leak DetectionWhole-Home RepipingGas Line RepairDrains & SewerDrain Cleaning & Sewer RepairMain Line Sewer CleaningSewer Camera InspectionGarbage DisposalWater Heaters & Water SystemsWater Heater RepairWater Heater InstallationTankless Water HeatersWater FiltrationPressure Regulator (PRV)Fixtures & MoreToiletsFaucets & FixturesShower & Tub ValvesKitchen & Bath InstallsOutdoor Hydrants & SpigotsCommercial PlumbingInspection & MaintenanceJob Stories About Reviews FAQ Contact Book Now Call (918) 891-1737 Book Online Text Us Request Service
Acts of Service Plumbing · Straight answers from a Tulsa plumbing family

No Hot Water? Quick Checks Before You Call a Plumber

Answer

The short answer

Acts of Service Plumbing technician at a gas water heater control knob next to the pilot lighting steps
The gas control knob and status light on a water heater we serviced in Collinsville.

By Ricky Hudson, owner, Acts of Service Plumbing.

On an electric water heater, check the breaker first, then the red high-limit reset button behind the top panel. On a gas water heater, look through the small window at the bottom of the tank to see if the pilot is lit, and relight it if it is not. If the reset button trips again or the pilot will not stay lit, call a plumber. Sometimes it is nothing major. Wind can blow a pilot out, and relighting it is the whole fix.

Start here

First: which kind of water heater do you have?

The checks are different, so start here. An electric tank has a power cord or conduit running into it and usually two small screw-on cover panels on the side. A gas tank has a gas line with a control knob near the bottom, a vent pipe coming out of the top, and a small sight-glass window on the bottom panel where the burner is.

If you have a tankless unit on the wall, the steps below do not apply. See our tankless water heater page or give us a call.

Electric

Electric water heater: two checks

1. Check the breaker

"If it's electric tank, you'd wanna check your breakers just to make sure one of them didn't get flipped." Look at your electrical panel and find the breaker for the water heater. If it has tripped, reset it and give the tank time to heat back up.

2. Push the high-limit reset button

If the breaker has not tripped, Ricky's next step is the reset button:

  • Turn the water heater breaker OFF first. Do not open the panel with the power on.
  • Electric tanks usually have two small cover panels, each held on by one or two screws. Behind them are the heating element and the thermostat that controls the temperature and tells the elements when to turn on.
  • Behind the top panel is a red high-limit reset button. When the water gets too hot, it kicks out and shuts the heater off.
  • Push it in. It is a lot like the red reset button on the bottom of a garbage disposal. If it had popped out, you will hear a click.
  • Put the panel back on and turn the breaker back ON. Check whether the water starts heating up.

What it means if the button had tripped

A reset button that popped once is worth watching. "If it happens again, definitely call the plumber, have him come out and test what's going on." Pushing the button over and over does not fix why it tripped.

Gas

Gas water heater: check and relight the pilot

1. Look at the pilot

Newer gas tanks are sealed, so you cannot reach in. There is usually a sight glass, a small window, on the bottom panel where the combustion chamber is. Look through it to see if the pilot flame is lit.

2. Relight it if it is out

Ricky's steps for newer control valves:

  • Turn the gas control knob to PILOT.
  • Press in and hold the button, usually black. Once the knob is on Pilot, it will push in.
  • Press the igniter (striker) button on the side. Like a charcoal grill starter, it makes a small spark inside the tank to light the gas. You should hear a little "poof" when the pilot lights.
  • Keep holding the button for about 30 seconds. On newer control valves, a small light will start blinking steadily, like a heartbeat.
  • Let go and turn the knob to HOT, or about 120 degrees. If your knob uses letters (A, B, C, D), A is about 120 degrees.
  • Watch that it stays lit.

3. If it goes back out

"If it goes back out, same thing. They'd wanna call the plumber to come out and take a look at it." A pilot that will not stay lit points to a part that needs testing, not to more relighting.

Tulsa weather

Why did my pilot go out?

"Sometimes they will blow out during a high windstorm. The wind will blow right down into the tank and blow those out. So sometimes it's nothing major. It's just relighting it."

On windy Tulsa days, that is worth knowing. If you lost hot water right after a big wind and the pilot relights and holds, you may be done. If it was calm out, or it will not stay lit, that is the time to call.

Our process

What we do when the water still will not heat

When you call us because the heater is not heating, Michael's process is the same every time: "we'll get out our tester and we'll start testing the gas control valve, and if we need to, we'll call tech support, 'cause a lot of times the water heater's under warranty." On a gas unit, no hot water is usually the pilot, the thermocouple or the gas control valve. On an electric unit, it is usually a heating element or the thermostat.

Our rule: when we replace a gas control valve, we replace the burner assembly with it on the same visit.

And you get a straight answer either way. "If your water heater can be repaired or needs to be replaced, the technician gets paid the same." Our techs are paid hourly, not on commission. You get your flat-rate price before any work starts. See Water Heater Repair for how a visit is priced.

Real job

A heater that would not stay lit in Collinsville

A tenant in a Collinsville rental called because the gas water heater would not stay lit, and we checked with the landlord before coming out. Our crew tested it and found a faulty gas control valve, which was still under its own warranty. The supplier wanted the old valve back first, so we drained the tank, disconnected the burner assembly, swapped the valve, replaced the burner assembly too and tested for function and leaks.

We also told the owner what else we saw: a relief valve that was not working, corroded supply nipples on top of the tank and sediment from hard water. Those are signs a tank is getting close to replacement. Read the Collinsville job story.

Leaks

No hot water and a leak? Deal with the water first

Sometimes no hot water comes with water in the pan. Ricky's answer: as long as there is a pan under the tank holding the water, it is not an emergency. Still shut the tank off so it does not get worse. There is usually a gate valve or ball valve on the cold-water line coming into the tank that you can turn off.

Sometimes what looks like the tank leaking is the temperature and pressure relief valve dripping into the pan. Either way, shut the tank off, because "it won't stop until the pressure gets dropped." Not every leak means a new tank. A leak at the flex connectors on top is common and an easy repair. A tank that is split inside has to be replaced.

Repair or replace

Is it time to repair or replace?

Plan on replacing a tank water heater around 10 to 15 years. We suggest replacing sooner if there is heavy rust where the flex connectors attach on top or inside the combustion chamber. Tulsa water is hard (5.2 to 8.2 grains per gallon depending on the treatment plant, according to the City of Tulsa), and the minerals settle in the bottom of the tank. That is the popping noise some tanks make, and it is why we suggest a yearly flush.

If your heater is older and losing hot water often, read Replacing a Water Heater in Tulsa and Why Is My Water Heater Popping?, or see our water heater installation service.

Call now or wait

When to call us

  • Try first: on an electric tank, check the breaker, then push the reset button with the power off. On a gas tank, check the pilot through the window and relight it.
  • Call us if the electric reset button trips again, the gas pilot goes back out after you relight it, you have no hot water and water in the pan or on the floor (shut the tank off first), or you are not comfortable opening a panel or working the gas control.
Next step

Still no hot water?

Book a visit with Acts of Service Plumbing online, or give us a call. We are a licensed, family-owned plumber in Tulsa serving Bixby and the surrounding area with flat-rate, upfront pricing. See our water heater repair service or schedule service.

Page last updated November 2026.

Questions

Straight Answers

Why do I have no hot water from my electric water heater?

Check the breaker first. If it is on, the high-limit reset button behind the top panel may have tripped. Turn the breaker off, push the red button in, then turn the breaker back on.

How do I know if my gas water heater pilot is out?

Look through the small window on the bottom panel of the tank. If you do not see a flame, the pilot is out.

How do I relight a gas water heater pilot?

Turn the knob to Pilot, hold the button in, press the igniter until you hear a poof, keep holding about 30 seconds, then turn the knob to Hot or about 120 degrees.

Why does my water heater pilot keep going out?

High wind can blow it out, and relighting fixes that. If it goes out again after you relight it, call a plumber to test the gas control valve.

What if my water heater reset button keeps tripping?

Call a plumber. A reset button that trips again needs to be tested, not pushed over and over.

Is a leaking water heater an emergency?

Not if a pan under it is holding the water. Still shut off the cold-water valve going into the tank so it does not get worse.

When should I call a plumber for no hot water?

Call if the electric reset button trips again, the gas pilot will not stay lit, or there is water in the pan or on the floor.

Acts of Service Plumbing service van at the shop
Acts of Service Plumbing

Real Techs. Real Answers.

Every job on this page is answered the way our own crew describes it — no scripts, no upsells.

Call Acts of Service Plumbing

Open 24 hours Monday through Saturday · Closed Sunday

(918) 891-1737