On the job in Broken Arrow




At a glance
- Where: Broken Arrow, OK 74014
- Completed: November 19, 2026
- Services: Slab leak detection & repair · Water leak repair
- Licensed: Oklahoma plumbing license #035596
What the homeowner was dealing with
This Broken Arrow home in ZIP 74014 had a leak in a water line under the slab, and the homeowner had already had it located by a leak-detection company before calling us for the repair. The marks were on the living room floor on the back side of a bathroom wall. The water line feeding that bathroom ran from a copper manifold, down into the slab, and across under the room.
We gave the homeowner an estimate for a direct repair through the floor. We also told them that if they wanted to price a reroute instead (running a new line overhead and abandoning the one under the slab), we would need to come back and look more closely at the manifold first. They chose to fix it where it was.
What the plan looked like before we started
A slab repair inside a finished room takes some planning. The estimate spelled it out: the carpet in the living room on the back side of the bathroom would need to be pulled back so we could reach the concrete. We would break up roughly a four-foot-by-four-foot section where the leak was located, dig down, and replace the leaking copper. We also warned that we might need to cut a two-foot-by-three-foot section of drywall behind the bathroom to tie the new line in. The room had to be cleared of anything in the way.
Before any work, the crew hung plastic sheeting floor-to-ceiling around the work area and covered the furniture and the light fixture. Breaking concrete indoors throws dust everywhere, and that sheeting is what keeps it in one corner of one room.
Once the concrete was out and the soil dug away, the copper under the slab looked the way leaking copper in Oklahoma clay usually does: heavily corroded, green, and wet around the failure.
Replacing the copper and reworking the manifold
Travis and Conner ran this one. The water to the house was shut off before any copper was cut. A large jackhammer was rented for the slab, since the opening was bigger than the usual access hole.
The leaking copper was replaced with half-inch PEX and tied back into the existing water line with half-inch press-to-expansion adapters. Here the job grew a little. The copper manifold where these lines come up out of the slab had been knocked around by the jackhammering, and the new connections needed room to hook up properly in the slab. So the crew reworked part of the manifold along with the water line. That is noted in the job record as an extra step, and it was done on the same visit.
With everything connected, the water came back on and the crew tested for leaks. There were none. Then the hole was filled back with sand and soil, and three bags of concrete went in to pour the slab back.
Why the manifold got extra attention
Copper manifolds that feed lines straight down into a slab are common in Broken Arrow homes of this era. The joints where the lines turn down into the concrete are tight, and when you are breaking concrete right beside them, the vibration and the swing of the jackhammer can stress fittings that were fine an hour earlier. Leaving a damaged fitting at the manifold just to finish faster would trade one leak for the next one.
The record for this job is direct: "we had to re work the manifold due to damage from jack hammering and from needing to be able to hook up in the slab." We would rather tell a homeowner that than pretend it did not happen.
Line repaired, manifold rebuilt, slab closed
By the end of the day the water line had been repaired, part of the manifold had been rebuilt, the system had been tested with no leaks, and the hole had been poured back. Photos of the finished area show the new concrete flush in the corner where the carpet had been pulled back.
The carpet and drywall are not plumbing. Before work started we let the homeowner know we are not responsible for drywall or carpet repair and referred a local contractor for that part. The plumbing repair itself carries our 90-day warranty.
How the choice gets made
For a slab leak there are usually two paths. A direct repair opens the floor at the located spot and fixes the pipe there. A reroute runs a new line through the attic or walls and abandons the old one under the slab. Neither is always better.
A reroute avoids concrete work, but it depends on where the manifold is and how the new line can reach the fixture. In this house, pricing a reroute would have meant another trip to study the manifold first. The leak had already been located precisely, the opening was in a carpeted room where the patch would be covered again, and the homeowner wanted it fixed now. That made a direct repair the straighter choice.
Whichever way you go, ask what happens to the rest of the old pipe. Copper that has corroded through in one spot in clay soil can fail elsewhere later. A direct repair fixes the leak you have; it does not renew the whole line. Being clear about that up front is part of giving a fair estimate.
What this means for your home
If your slab leak is in a finished room, ask how the area will be protected, how large the opening will be, and whether there is any chance drywall will need to be opened to make the connection. Ask too whether a reroute is an option. On some homes it means no concrete work at all; on others, like this one, a direct repair at the located spot is the straighter path.
Before your plumber arrives, clear the room near the marked spot. It saves time and keeps your things out of the dust.
Services on this job: Slab leak detection & repair · Water leak repair · Plumber in Broken Arrow · How our pricing works · All job stories
Straight Answers
Can a slab leak be fixed without rerouting the whole line?
Yes, when the leak has been located. In this Broken Arrow home we opened about a four-by-four section of slab at the located spot, replaced the leaking copper with PEX, reworked part of the manifold, tested for leaks and poured the concrete back.

