On the job in Collinsville




At a glance
- Where: Collinsville, OK 74021
- Completed: November 11, 2026
- Services: Slab leak detection & repair · Water leak repair
- Licensed: Oklahoma plumbing license #035596
What the homeowner was dealing with
This job started before our crew ever picked up a jackhammer. The homeowner in Collinsville, ZIP 74021, had a leak somewhere under the slab, and a leak-detection company had already been out to trace it. Their report did the hard part: it put the leak on a half-inch copper line that runs under the floor from the washing machine manifold over to the manifold that feeds the master bathroom vanity, which sits to the right of the tub.
The locator traced the line at roughly a foot to a foot and a half deep where it runs level under the slab, and the loudest point of the leak noise was right behind the washer. They marked that spot with red tape and a red arrow and X on the floor. That mark is where we planned to dig.
By the time we arrived the laundry area had been cleared out, and drying fans and a dehumidifier were already running on the floor. That tells you how much water had been coming up.
Reading the locate before breaking concrete
A good locate saves a homeowner a lot of concrete. Instead of trenching across the laundry room hunting for the pipe, our estimate scoped one access hole at the marked point, on the half-inch hot water line inside the closet area that feeds the hot side of the washer manifold.
The plan we wrote up was simple and we followed it: bust up the concrete at the mark, dig down to the water line, make the repair, turn the water back on, look at it and feel it to be sure nothing is leaking, then put the dirt back and pour concrete back to a rough finish. We also told the homeowner up front that we would keep the cut-out copper so they would have it if their insurance company wanted to see it, and that we would photograph the work before, during and after.
When the hole was open, the copper showed exactly what the sound had suggested. The pipe wall had a hole worn through it, and the outside of the copper was green with corrosion where it sat in the soil. You can see the pinhole in the piece we removed in the photos below.
Cutting out the bad copper and tying in PEX
Michael, Josh and Kagen worked the repair as a three-person crew. With the water off, they broke out the slab in front of the washer wall and dug down by hand around the line until there was enough room to cut cleanly on both sides of the leak.
They cut out the damaged half-inch copper and replaced it with half-inch PEX. The connection to the copper on each end was made with two half-inch press-to-expansion adapters, so the new pipe joins the old copper with a pressed fitting on the copper side and an expansion ring on the PEX side. Parts for the actual repair were short: the two adapters, a length of half-inch PEX and the PEX rings.
Once the new section was in, the water went back on. The crew watched and handled the joints with the line under pressure before anything was buried, because once the concrete goes back you do not want to be opening it again. No leaks. Then the soil went back in and the concrete was poured back level with the floor around it.
Why the laundry wall matters on a slab home
Many slab homes in the Tulsa area, including newer builds in Collinsville, use manifolds: one supply point that splits into separate lines running under the floor to each fixture group. That design is the reason the locator could name this leak so precisely. The line had a starting point (the washer manifold), an end point (the vanity manifold in the master bath) and a known path between them.
It also means the problem is usually one line, not the whole house. Here, only the hot line serving that run needed work. The other lines coming out of the manifold were left alone, and the rest of the laundry plumbing, the drain and the gas line beside it were not disturbed.
This visit was the access and the repair together. The estimate split it into two pieces, getting to the leak and fixing it, so the homeowner could see what each part covered. Both were finished the same day.
Water back on, floor closed up
At the end of the visit the house had water again, the new PEX section had been checked under pressure with no leaks, and the hole in front of the washer was filled and covered with new concrete. The homeowner kept the cut section of copper for their insurance company, along with the photos from each stage of the job. The repair carries our 90-day warranty.
Flooring, trim and the cosmetic finish of the patch are separate from the plumbing repair. The concrete was poured back to a rough finish, which is what the estimate called for.
What a homeowner can do while waiting
Between the locate and the repair, a slab leak keeps running. If water is coming up through the floor, shut the house off at the meter or the main shutoff whenever you are not using water, and turn it back on only when you need it. Pull wet rugs and boxes away from the spot and run fans; this homeowner already had a dehumidifier and air movers going, which keeps the framing and drywall from soaking up more water.
Watch the water meter with everything off. If the leak indicator keeps spinning, the leak is still active and still costing you. Take a short video of it; insurance adjusters and plumbers both find it useful. Finally, clear the area around the marked spot. On this job the laundry room shelving and floor were already empty, so the crew could start breaking concrete right away instead of moving belongings first.
What this means for your home
If someone tells you that you have a slab leak, ask two questions. First, has the leak been located to a specific line and spot? A locate is what lets a plumber open one small area instead of tearing up a room. Second, what will be done to test the repair before the concrete goes back? On this Collinsville job the answer was a marked spot from a leak-detection company and a pressure check with the water on before burial.
Keep the damaged pipe and ask for photos. Insurance adjusters often want to see both.
Services on this job: Slab leak detection & repair · Water leak repair · Plumber in Collinsville · How our pricing works · All job stories
Straight Answers
Do you have to tear up the whole floor to fix a slab leak?
No. When the leak has been located to one spot, we open only that area. In this Collinsville home we broke out one section of slab at the marked point behind the washer, replaced the leaking half-inch copper with PEX, tested it and poured the concrete back.

