Emergency & LeaksEmergency PlumbingWater Leak RepairSlab Leak DetectionWhole-Home RepipingGas Line RepairDrains & SewerDrain Cleaning & Sewer RepairMain Line Sewer CleaningSewer Camera InspectionGarbage DisposalWater Heaters & Water SystemsWater Heater RepairWater Heater InstallationTankless Water HeatersWater FiltrationPressure Regulator (PRV)Fixtures & MoreToiletsFaucets & FixturesShower & Tub ValvesKitchen & Bath InstallsOutdoor Hydrants & SpigotsCommercial PlumbingInspection & MaintenanceJob Stories About Reviews FAQ Contact Book Now Call (918) 891-1737 Book Online Text Us Request Service
Acts of Service Plumbing job story · Tulsa, OK 74135 · Completed November 16, 2026

Water Heater Repair in Tulsa, OK: New Slim Gas Tank With a Factory-Damaged Burner Sorted Out Under Warranty

Job photos

On the job in Tulsa

Underside of the slim gas water heater showing the burner assembly that sputtered — Tulsa, OK 74135 job photo by Acts of Service Plumbing
Burner assembly that sputtered
New flexible gas connector and shutoff valve feeding the slim gas water heater — Tulsa, OK 74135 job photo by Acts of Service Plumbing
Gas line upgraded with a shutoff
Gas control valve on the new 40-gallon slim gas water heater — Tulsa, OK 74135 job photo by Acts of Service Plumbing
Gas control on the new tank
Expansion tank and piping above the new slim water heater in the closet — Tulsa, OK 74135 job photo by Acts of Service Plumbing
Expansion tank added
Job facts

At a glance

The call

What the homeowner needed

This Tulsa home in ZIP 74135 has its water heater tucked in a tight closet, which is why the homeowner needed a slim model. A standard 40-gallon tank is too wide for spaces like this; a slim 40-gallon gas tank is taller and narrower and fits where the old one stood.

The homeowner approved our estimate for a new 40-gallon slim gas water heater. Because they approved the work, we refunded the service charge from the first visit. That is how our service call works: it is waived when you approve the repair.

What we found

A new tank with a bad burner

The install itself went in, but something was wrong with the new heater. The burner assembly was "puttering," in our tech's word. That is a sputtering, uneven flame instead of a steady blue burn. On a brand-new heater, that is not a venting or gas-pressure problem you fix with an adjustment. Travis and Conner looked it over and concluded the burner assembly had been damaged at the factory.

Rather than send the homeowner off to deal with the manufacturer, they called A.O. Smith directly from the job. A.O. Smith agreed, issued the replacement part and gave us a warranty claim number. The burner replacement then went on our schedule as a return visit, covered under the manufacturer's warranty.

While they were in the house they spotted one more thing. The washing machine supply hoses were leaking at the boiler drains they connect to. That is not part of the water heater job, so we told the homeowner about it and left the decision with them.

The fix

Bringing the closet up to code

The estimate covered more than dropping in a tank. A water heater install is the moment to fix everything around it that is out of date, and in this closet that meant several pieces:

  • A new drip pan under the heater.
  • An upgraded gas line, with a new flexible connector and a new shutoff valve at the heater.
  • A new main water shutoff valve.
  • An expansion tank on the cold side.
  • Water hammer arrestors.
  • Haul-away and disposal of the old tank.

If any venting outside the mechanical room had needed replacing, that would have been extra, and we said so in the estimate. The heater itself is an A.O. Smith, the brand we use on tank water heaters.

On the job

Why an expansion tank and arrestors

Many homes in this part of Tulsa now have a pressure-reducing valve or a check valve at the meter. That makes the plumbing a "closed" system: when water heats up and expands, it has nowhere to go but back into your pipes. An expansion tank gives that water a place to go, which takes stress off the tank, the relief valve and the fixtures.

Water hammer arrestors deal with the bang you sometimes hear when a washer or dishwasher valve snaps shut. They are small, cheap and worth adding while the walls around the heater are open.

None of that would have helped with the burner, though. A sputtering flame on a new appliance is a parts problem, and the right move was to stop and get the manufacturer involved rather than keep tinkering with a gas appliance.

The result

Where things stood when we left

When the crew left on November 16, the new 40-gallon slim gas heater was installed with its drip pan, upgraded gas connection, new main shutoff, expansion tank and arrestors. The manufacturer had approved the warranty part for the burner assembly, and the homeowner was being scheduled for the swap. The homeowner also knew about the leaking washer hoses so they could deal with them.

That is the honest status. The burner swap was a follow-up visit, not something we finished that night, and we are not going to describe it as done before it was.

Why slim

Fitting a tank into a tight closet

Many Tulsa homes built in the 1970s and 1980s put the water heater in a hall closet or a small mechanical room sized for the tank that was there on day one. Standard 40-gallon gas tanks have grown wider since then, partly because of added insulation. When the old tank fails, a standard replacement may not fit through the door or may sit too close to the walls for the required clearances.

A slim tank solves that by going taller and narrower while holding the same 40 gallons. The trade-off is height: you have to check that the vent connector and draft hood still line up with the existing flue. That is why the estimate flagged venting outside the mechanical room as a possible extra. If the flue had needed rework, we would have said so before starting.

On this job the closet also got a new main water shutoff. If anything ever goes wrong with the heater, the homeowner can now shut the house off fast without hunting for the meter.

Takeaway

What this means for your home

New appliances can arrive with defects. If a brand-new gas water heater sputters, makes a puttering sound or has a flame that will not settle down, turn it off and call your installer. Do not keep relighting it. A licensed plumber can tell the difference between an installation problem and a part that failed at the factory, and can work the warranty with the manufacturer for you.

If your heater sits in a closet, ask about a slim model before you assume you need to rebuild the closet. See replacing a water heater in Tulsa and no hot water? quick checks.

Services on this job: Water heater repair · Water heater installation · Plumber in Tulsa · How our pricing works · All job stories

Questions

Straight Answers

What should I do if my new gas water heater burner is sputtering?

Turn the heater off and call your installer. On this Tulsa job the burner assembly on a new 40-gallon slim gas heater was damaged at the factory, so we called A.O. Smith, got the warranty part and scheduled the replacement.

Acts of Service Plumbing service van at the shop
Acts of Service Plumbing

Real Techs. Real Answers.

Every job on this page is answered the way our own crew describes it — no scripts, no upsells.

Call Acts of Service Plumbing

Open 24 hours Monday through Saturday · Closed Sunday

(918) 891-1737