Emergency & LeaksEmergency PlumbingWater Leak RepairSlab Leak DetectionWhole-Home RepipingGas Line RepairDrains & SewerDrain Cleaning & Sewer RepairMain Line Sewer CleaningSewer Camera InspectionGarbage DisposalWater Heaters & Water SystemsWater Heater RepairWater Heater InstallationTankless Water HeatersWater FiltrationPressure Regulator (PRV)Fixtures & MoreToiletsFaucets & FixturesShower & Tub ValvesKitchen & Bath InstallsOutdoor Hydrants & SpigotsCommercial PlumbingInspection & MaintenanceJob Stories About Reviews FAQ Contact Book Now Call (918) 891-1737 Book Online Text Us Request Service
Acts of Service Plumbing job story · Catoosa, OK 74015 · Completed November 4, 2026

Low Water Pressure in Catoosa, OK: Multiple Fixtures Diagnosed and Fixed in One Visit After a Recent Re-Plumb

Job photos

On the job in Catoosa

Add-a-tee connector with the internal washer that was restricting water flow — Catoosa, OK 74015 job photo by Acts of Service Plumbing
Washer inside the add-a-tee
Clogged mesh inlet screens in the washing machine water valve — Catoosa, OK 74015 job photo by Acts of Service Plumbing
Clogged washer inlet screens
Water supply connections under the three-compartment sink — Catoosa, OK 74015 job photo by Acts of Service Plumbing
Supply lines under the three-compartment sink
Three-compartment sink running at full pressure after the repair — Catoosa, OK 74015 job photo by Acts of Service Plumbing
Full flow at the three-compartment sink
Faucet aerator removed from a lavatory faucet with a trickle — Catoosa, OK 74015 job photo by Acts of Service Plumbing
Lavatory aerator
Job facts

At a glance

The call

What the customer was dealing with

The building in Catoosa, ZIP 74015, had recently had some new plumbing work done, and afterward the water pressure was bad in several places. The customer called us to diagnose it. Low pressure at more than one fixture right after a re-plumb points to the new work, not the city supply, and that is where Trystan and Kagen started.

The building has a commercial-style kitchen with a three-compartment sink and a hand sink, a washing machine, and upstairs restrooms.

What we found

Four separate causes

Low pressure is rarely one thing in a building with this many fixtures. The crew went through each complaint on its own.

The kitchen. Turning on the hand sink killed the pressure at the three-compartment sink entirely. Both sinks were fed through add-a-tee connectors, a fitting that lets one supply stop feed two lines. When the crew disconnected the lines, they found each add-a-tee had a washer seated inside it in a way that blocked the water.

The washing machine. The customer said it filled very slowly. The crew pulled the supply hoses and found the mesh screens inside the machine's water valve clogged with debris. They also found the hot and cold hoses were reversed.

Upstairs restrooms. In the women's room, the three lavatory faucets were only putting out a trickle. In the men's room, the urinal was running hot water.

The fix

What we did about each one

  • Add-a-tees: removed the blocking washers and sealed the connections with Teflon tape instead, then reconnected both sinks. Both now get full pressure and work together without one starving the other.
  • Washer: took the inlet screens out, cleaned them and reinstalled them. Swapped the hot and cold hoses to the correct sides. Ran the washer to test it, and it filled at full pressure.
  • Lavatory faucets: removed the aerators on the first two faucets but left the mesh screens in place so they would not spray, and replaced the aerator on the far right faucet. All three sinks now run properly.
  • Urinal: the urinal is plumbed to the hot water supply. Correcting it means major work, so we explained that to the customer rather than start opening walls on a diagnosis visit.

We also noted that the drain assembly in the kitchen needed replacing and said we would send an estimate for that.

On the job

Why new plumbing can lower pressure

When a line has been opened and worked on, debris gets loose: bits of pipe shavings, sealant, sediment that was sitting in old pipe. The first place it lands is the smallest opening downstream, which means faucet aerators and the fine screens in appliance valves. That is why aerators and washer screens are the first things to check after any plumbing work, and why clogged screens at several fixtures at once make sense right after a re-plumb.

The add-a-tees are a different kind of problem. That was not debris; it was a fitting assembled with a washer where it restricted flow. When two fixtures share a supply through one fitting, a restriction there shows up exactly the way the customer described it, with one sink starving the other.

The result

Full pressure where it counts

By the end of the visit the kitchen sinks, the washing machine and the upstairs lavatory faucets were all running at full pressure. The customer had a clear explanation of the urinal and an estimate coming for the kitchen drain assembly. The work carries our 90-day warranty, and a senior discount was applied.

Quick checks

What you can check yourself first

Some low-pressure problems are easy to check before you call. Unscrew the aerator from a slow faucet and look at the screen. If it is packed with grit, rinse it and run the faucet without it for a few seconds to flush the line. If pressure comes back, that was the problem.

For a washing machine that fills slowly, turn off both supply valves, unscrew the hoses at the machine and look inside the inlet ports. The small screens there catch sediment. They can be pulled out gently and rinsed. While you are back there, check that the hot hose goes to the hot inlet; in this building they were swapped.

If one fixture loses pressure when another turns on, that is not something an aerator explains. It points to a shared supply that is restricted or too small, like the add-a-tees in this kitchen. That is when a plumber should take the lines apart.

Also check whether the problem is hot only, cold only or both. Low pressure on hot only points toward the water heater or its connections. Low on both, at one fixture, points to that fixture. Low on both, everywhere, points to the supply coming into the building. Telling your plumber which pattern you see shortens the diagnosis and the bill.

Takeaway

What this means for your property

If your pressure dropped right after plumbing work, check the simple things first: unscrew a faucet aerator and look for debris, and look at the screens where your washer hoses connect. If pressure drops at one fixture when another turns on, the problem is usually in a shared fitting or a too-small supply, and that needs a plumber.

If pressure is low everywhere in the house, including outside, that is a different problem, often the pressure-reducing valve. See our plumbing questions page.

Services on this job: Commercial plumbing · Faucet & fixture installation · Plumber in Catoosa · How our pricing works · All job stories

Questions

Straight Answers

Why is my water pressure low after new plumbing work?

Often debris clogs aerators and appliance screens, or a fitting restricts flow. In this Catoosa building, washers inside add-a-tee connectors starved the kitchen sinks, and clogged washer screens and aerators caused the rest. All were fixed in one visit.

Acts of Service Plumbing service van at the shop
Acts of Service Plumbing

Real Techs. Real Answers.

Every job on this page is answered the way our own crew describes it — no scripts, no upsells.

Call Acts of Service Plumbing

Open 24 hours Monday through Saturday · Closed Sunday

(918) 891-1737