Maintaining a smooth-running home requires proper planning, time, and resources. At Acts of Service Plumbing, we offer affordable water heater tank repairs, flexible scheduling, and on-time arrival. We value our customers, and we communicate this through our actions. Because we genuinely, care about our customers we have put together this great article!


  1. Gas Leak

Your home’s lack of hot water could become a permanent fixture due to a gas line leak. Prior to calling a plumber or attempting to fix a gas water heater on one’s own with home tools, it is crucial to check all connections for leaks. Close the main valve.  The pipes should be checked for moisture or any strange odor emanating from the gas supply.

2. Water heater tank leak

Tanks for water heaters are not intended to leak. A water heater can only operate if the tank is full of waterIf there is no hot water and water is visible on the ground around the hot water tank’s base, you most likely have a leaky tank.

Empty tanks are extremely dangerous and inefficient in terms of energy use. Check all of the pipes’ connections, valves, and other hardware on the appliance. Check the tank compartment to see whether they are locked.

If there is water in the compartment, your device probably has to be replaced

  1. Gas Valve Defect

Check the gas input valve and gas supply tube if you have a gas water heater and there is no hot water. Check the gas valve if there are no leaks.. It must be placed correctly and be safe. Then confirm that the gas is turned on once more.

To find out if the gas valve is operating properly, look at the pilot light. The pilot may need to be lit several times. It needs to remain burning. If not, the gas supply may be limited as a result of the gas line’s obstruction.

4, Pilot Light Is Out

Your water heater’s pilot light might be out if the hot water faucet has turned cold. When this occurs, there are typically warning signs that the pilot light went out.

  1. Faulty Electric Water Heater

You won’t have cold water when you awaken thanks to gas or electric water heaters.  Not a water heater problem, but an electrical one, could be the cause.

Replace the main energy source from power outlets with another electric item that has its own internal battery backup system as another way to test this idea. There is no power going to your electric water heater if switching power sources does not turn on any heated faucets.

Finding any loose connections to the water heater and resetting any blown fuses in the circuit breaker box will fix the problem of not having hot water, which is a typical issue. If the breaker tripped, your home will once again have access to warm water after roughly an hour. A circuit breaker that keeps tripping signifies a poor signal, so press the reset button.

  1. A broken thermostat

The thermostat needs to be replaced if it is damaged. Even if the thermostat is adjusted properly, difficulties due to silt buildup can result from lack of routine maintenance. Drain and clean your water heater to get rid of this.

One of the most frequent causes of no longer having hot water in your home is a high-temperature cutoff switch that has tripped. Flipping the switch and pressing a button will fix it.

When you press the reset button, the water heater should make a clicking noise before power comes back on.

  1. An erroneous heating element

If there is no hot water in your home, the heating elements may be the issue. A new water heater is preferable to repairing an old one because they only last ten years. However, be sure to totally shut off your furnace if you need to replace your heating elements.

  1. Size of Water Heater Tank

Your home won’t be energy efficient and will run out of hot water more quickly if your tank is too small. When it was just the two of you and your spouse, the device may have been effective. However, as your family grew, there was a greater demand for hot water and a lot hotter baths. This suggests that you should increase the capacity of your hot water tank.


Whether a water heater is an electric or gas model determines how long it takes for it to recover. The recovery time of a gas water heater is half that of an electrical one. A 40-gallon electric water heater needs about two hours to recharge. An electric water heater with 40 gallons takes almost twice as long to recover as an equivalent gas device (about four hours).

Avoid using any hot water while you’re recovering for the quickest return of hot water. If you don’t use hot water while the tank is filling up, your heater will continue to heat the water.

If you draw water while the recovery process is underway, you’ll be adding chilly water to your tank. This will only increase the amount of time it takes for your water heater to fully recover and start supplying hot water. If you take a sip of water too soon, it might only be warm or you might only have a brief period of hot water before it cools off again.


Reset your water heater.

You could observe that your water heater’s circuit breaker trips regularly. By doing the following, you can try to carefully reset your water heater:

To eliminate any dangers of electrocution, you must turn the water heater breaker to the off position.

Without touching any wiring, remove the panel from the water heater’s upper half.

Find the red reset button, then press it.

A specialist can always carry out this. You will need to contact a plumbing professional if you are unable to restart your water heater.

Check to see whether anyone else in your home was using the hot water.

The tank of conventional water heaters normally has a capacity of 40 gallons. It may be that your tank exhausted the current supply of hot water and is filling back up with cold water if you have a large family and everyone is consuming a lot of hot water at once.

Check if you may get some hot water back by waiting a short period. If you do and you frequently run out, your tank might not be large enough for your family..

Look for leaking water around your tank.

A leak around the lowest portion of the tank is a frequent problem that causes water heaters to run out of hot water more quicker than usual. By looking at the area of ground around your water heater, you might quickly find a leak.

Verify whether there is water in the heater’s compartments.

Your water heater’s compartments could become flooded by a tank leak, harming your thermostats in the process. By removing the panels, you may inspect these locations. Replace a damaged thermostat.

Activate the gas.

Make sure your gas is on and there are no gas leaks if you have a gas water heater. If the gas is on, though, and you can smell As soon as you notice a gas leak, shut off your gas valve. Report gas leaks for your family safety.

Check the pilot light.

If you have a broken thermocouple in your water heater, pilot lights frequently go out. According to the directions on the appliance or in your manual, check the pilot light in the water heater’s lower compartment and relight it.


Get in touch with act of service plumbing a nationwide plumbing company, if your house still has a hot water shortage. We have knowledge and experience to identify the source of any hot water issue, from gas line services to water heater repair and installation.

Fun Fact

What year did Rick Hudson begin his plumbing career? Find the answer on our About Us | Plumbing Tulsa | Acts of Service Plumbing! Hire a seasoned plumber with years of experience.

One of the many companies we’ve had the pleasure of serving faithfully over the years is Paul Davis Corporate – Restoration and Emergency Service Provider. Learn more about them today!